Dakota Digital MCL-2011(-R) Service Manual download pdf (Page 7)

MAN# 650369

RANGE

RANGERANGE

RANGE Distance to Empty setup

The range reading will initially show the word range until a tank of gas has been driven to allow the gauge to complete its

setup based on your driving. Begin with a full tank of gas and do not refill it until it gets below ¼ tank of gas. This can be done on

multiple trips as long as no fuel is added before it gets low enough. After the initial setup the display will show r followed by the

calculated distance to empty. This will count down, making adjustments as necessary, until the range is 35 miles (56km) or less and

then it will show r Lo. The gauge will continue to make adjustments to match your driving habits with each fill up. After the initial

setup you are not required to wait for the fuel to get below ¼ tank before refilling.

• Press and release the switch until “RANGE” is displayed, then press and hold the switch until “ - ” is displayed.

• The display will show “oFF” or “oN”. Press and release the switch to change to the desired setting.

•

Press and hold the switch until “ - ” is displayed to select the setting.

•

OFF turns the range display off.

•

Turning the function on will access the following menus

donE (exits the setup)

rESEt (resets the gauge to beginning of the initial range learning)

sender (used to change or reset the fuel gauge readings)



Hd (set to factory default sending unit)

 CSt (set to a custom fuel curve)

•

SET 00 (set new empty reading, done indicates it was stored, error indicates the signal

is out of range)

•

SET 99 (set new full reading)

• Press and release the switch to select the desired fuel setup menu, press and hold it until “ - ” is displayed, and then release the

switch to view or go on.

• A press and hold will save the setting or exit back to the menu.

• done is the first menu displayed, a press and hold will exit fuel set up at this point.

• rESEt will begin the initial range learning again. You must begin with a full tank of gas and then ride it down to less than ¼ tank.

This can be done in multiple trips as long as the tank is not filled in between. The range display will show range until this is

completed and then begin showing the distance to empty.

• FUL - RESET This will set the fuel gauge setup points back to stock values.

• FUL - SET 99 This will set a new full reading for the fuel gauge to allow for customization or improved range accuracy.

done indicates it was stored, error indicates the signal is out of range

• FUL - SET 00 This will set a new empty reading for the fuel gauge to allow for customization or improved range accuracy.

done indicates it was stored, error indicates the signal is out of range

InFO

InFOInFO

InFO Info menu

Displays the current software revision on the speedometer display. (no changes can be done in this menu)

odoMK

odoMKodoMK

odoMK Odometer preset

The odometer can be preset by the customer within the first 100 miles. Once the odometer has more than 100 miles, the menu option

will no longer be displayed. Make sure you have correctly selected the units to be either MPH or km/h first. The odometer will be set

in the selected units. The reading shown when entering the preset menu will be the value obtained from the ECM. Once you have

preset the miles you cannot change it again.

WARNING!!: This only allows setting odometer to the nearest mile. Do not use tenths! For example a mileage of 65432.1

should be set to “065432” using this method. If the tenths digit is used, the odometer will read 10 times too high.

• Press and release the switch until “-odoMK” is displayed, then press and hold the switch until “ - ” is displayed.

• The current ECM odometer reading will be displayed with the left most digit flashing.

• Press and release the switch to increment the digit. Press and hold the switch to move to the next digit to the right.

• Continue until the right most digit has been set. Press and hold the switch and the speed display will show “No”.

• Press and hold the switch while “no” is displayed to go back and continue changing the odometer display. Turn the key off to

cancel any changes.

• Press and release the switch to change to speed display to “yes”. Press and hold the switch while “yes” is displayed to save the

current odometer reading.

1 2 3 4 5 6 7 8 9

Comments to this Manuals

No comments

Dakota Digital MCL-2011(-R) Service Manual Page 7

Comments to this Manuals

Related products and manuals for Motor vehicle electronics Dakota Digital MCL-2011(-R)