Dakota Digital MCL-2011(-R) Service Manual download pdf (Page 4)

MAN# 650369

SPEEDOMETER SETUP

Press and hold the switch while turning the key on and starting the engine. Once the engine is running, release

the switch. Press and release the switch to change the menu selection.

dIAG

dIAGdIAG

dIAG Diagnostics mode for checking/clearing trouble codes

• Press and release the switch until “dIAG” is displayed, then press and hold the switch until “ - ” is displayed.

• Release the switch. The display will show “ENGINE”, “SECvRE”, ”ABS”, or “DoNE”.

• Press and release the switch to change the selection, press and hold the switch until “ - ” is displayed to begin reading the stored

codes for the particular system.

• Release the switch. The display will show the current codes, “none”, or “no rsp”. Press and release the switch to move to the

next stored code. After all codes are displayed the module part number will be scrolled across the screen. To clear codes, press

and hold the switch when “end” is displayed. Consult a service manual for trouble code descriptions.

SPEED CALIBRATION

The speed calibration is not required unless you have changed out the rear pulley, sprocket, stock transmission, or

stock tires.

ADJvST

ADJvST ADJvST

ADJvST Adjust speedometer calibration

• Press and release the switch until “AdJvSt” is displayed, then press and hold the switch until “ - ” is displayed.

• Release the switch. The display will show “fastEr” or “sLOWX”. Faster will allow you to increase the speedometer reading, slow

will allow you to decrease the speedometer reading.

• Press and release the switch to change, press and hold the switch to continue. The display will change to “CL” and a number from

75 to 125. This is the calibration ratio that is applied to the reading that the ECM is providing. 110 will be 10% faster, 90 will be

10% slower. Think of the number displayed as a percentage.

Actual speed

----------------------------- x current Cal ratio (100 by default) = new Cal ratio

speedometer reading

• Press and release the switch to change the cal ratio. When the desired cal ratio is shown, press and hold the switch to save it.

vNIT

vNIT vNIT

vNIT Speed unit

• Press and release the switch until “vnit” is displayed, then press and hold the switch until “ - ” is displayed.

• Release the switch. The display will light up the current speed unit (MPH or km/h).

• Press and hold the switch to keep the current unit or press and release the switch to change the unit.

S SET

S SET S SET

S SET Miles to Next Service setup

The service mileage is a countdown mile meter. The service mile display can be disabled or can be set to count down from

500 – 7500 miles. If the service mileage is enabled and it gets to 0 miles it will display “S -DvE” each time the key is turned on. If the

push button switch is pressed and held while “S -dve” or “S” and a mileage is displayed, the service miles will be reset to your preset

value.

• Press and release the switch until “S set” is displayed, then press and hold the switch until “ - ” is displayed.

• Release the switch. The current setting will be displayed, “OFF” or a mileage from 500 - 7500.

• Press and release the switch until the desired setting is displayed.

• Press and hold the switch until “ - ” is displayed.

PERF

PERF PERF

PERF Performance menu setup

The performance readings can be turned on or off. When they are turned off the message display will only toggle through the

mileage readings.

• Press and release the switch until “PErF” is displayed, then press and hold the switch until “ - ” is displayed.

• Release the switch. The current setting will be displayed (on or oFF).

• Press and release the switch until the desired setting is displayed.

• Press and hold the switch until “ - ” is displayed.

nIgHt

nIgHtnIgHt

nIgHt Night Dimming

Your display system has a dimming feature that dims the display intensity automatically at night. Normally the system is at full

brightness for daytime viewing. To have the system at full brightness all of the time, go into the setup menu as described above and

select “ngt” (night). Press and release the trip switch to select “OFF” instead of “on”. Press and hold the trip switch to save the new

setting.

• Press and release the switch until “nIgHt” is displayed, then press and hold the switch until “ - ” is displayed.

• Release the switch. The current setting will be displayed. (ON, OFF).

• Press and release the switch until the desired setting is displayed.

• Press and hold the switch until “ - ” is displayed to save the setting.

1 2 3 4 5 6 7 8 9

Comments to this Manuals

No comments

Dakota Digital MCL-2011(-R) Service Manual Page 4

Comments to this Manuals

Related products and manuals for Motor vehicle electronics Dakota Digital MCL-2011(-R)