Dakota-digital MCL-3204 User Manual download pdf (Page 2)

MAN# 650284:F

MOUNTING

The gauge will mount using the original housing, grommet, and screws. Unbolt the two screws from the back plate

at the back of the gauge housing, then unplug the factory gauge, noting the position of the grommets. There is one

grommet on the front between the gauge and housing and one on the back between the housing and the back plate. Install

the Dakota Digital gauge in reverse order installing grommets and then plugging into the factory plug and securing with the

two screws.

SPEEDOMETER SETUP

Press and hold the switch while turning the key on and starting the engine. Once the engine is running, release the

switch. Press and release the switch to change the menu selection.

dIAG

dIAGdIAG

dIAG Diagnostics mode for checking/clearing trouble codes

• Press and release the switch until “dIAG” is displayed, then press and hold the switch until “ - ” is displayed.

• Release the switch. The display will show “ENGINE”, “SECvRE”, “ABS”, or “DoNE”.

• Press and release the switch to change the selection, press and hold the switch until “ - ” is displayed to begin reading the stored

codes for the particular system. Release the switch. The display will show the current codes, “none”, or “no rsp”.

• Press and release the switch to move to the next stored code. After all codes are displayed the module part number will be

scrolled across the screen. To clear codes, press and hold the switch when “end” is displayed. Consult a service manual for

trouble code descriptions.

SPEED CALIBRATION

The speed calibration is not required unless you have changed out the stock transmission, pulley, or tires.

ADJvST

ADJvST ADJvST

ADJvST Adjust

• Press and release the switch until “AdJvSt” is displayed, then press and hold the switch until “ - ” is displayed.

• Release the switch. The display will show “fast” or “sLOWX”. Fast will allow you to increase the speedometer reading, slow will

allow you to decrease the speedometer reading.

• Press and release the switch to change, press and hold the switch to continue. The display will change to “CL” and a number from

0.75 to 1.25. This is the calibration ratio that is applied to the reading that the ECM is providing. 1.10 will be 10% faster, 0.90 will

be 10% slower.

Actual speed

----------------------------- x current cal ratio (1.00 by default) = new cal ratio

speedometer reading

•

Press and release the switch to change the cal ratio. When the desired cal ratio is shown, press and hold the switch to save it.

vNIT

vNIT vNIT

vNIT Speed and temperature unit

• Press and release the switch until “vnit” is displayed, then press and hold the switch until “ - ” is displayed.

• Release the switch. The display will light up the current speed unit (MPH or km/h). The temperature unit will be °F with MPH and

°C with km/h.

• Press and hold the switch to keep the current unit or press and release the switch to change the unit.

•

Press and hold the switch until “ - ” is displayed to save the setting.

S SET

S SET S SET

S SET Miles to Next Service setup

The service mileage is a countdown mile meter. The service mile display can be disabled or can be set to count down from

500 – 7500 miles. If the service mileage is enabled and it gets to 0 miles it will display “S -DvE” each time the key is turned on. If the

push button switch is pressed and held while “S -dve” or “S” and a mileage is displayed, the service miles will be reset to your preset

value.

• Press and release the switch until “S set” is displayed, then press and hold the switch until “ – ” is displayed.

• Release the switch. The current setting will be displayed, “OFF” or a mileage from 500 - 7500.

• Press and release the switch until the desired setting is displayed.

•

Press and hold the switch until “ - ” is displayed to save the setting.

1 2 3 4 5 6

Comments to this Manuals

No comments

Dakota-digital MCL-3204 User Manual Page 2

Comments to this Manuals

Related products and manuals for For the car Dakota-digital MCL-3204