Dakota-digital MCL-3204 User Manual download pdf

MAN# 650284:F

MODEL MCL-3204

3-3/8” SPEEDOMETER/TACHOMETER for 2004 – up

GAUGE SETUP AND CALIBRATION

The setup menus are entered by holding the switch in while turning the key

on. The menus are as follows:

Menu Description

dIag (EngInE, seCURE, ABS, DONE) read diagnostic codes

ADJvST (FASTER, SLOWER) (75 - 125) adjust calibrate speed

vnIt (MPH, km/h ) select speed & temp unit

S SET (OFF, 500 - 7500) miles to service setting

PERF (ON, OFF) turn on/off performance displays

NIGHT (ON, OFF) turn on/off automatic night dimming

WXARN

RPM

(shown on bar graph) set RPM shift warning point

WXARN

(9.0- 12.1) set low volt warning point

HI F-C (200F - 420F or 93C - 215C) set temperature warning point

GEAR (DONE, PRESET, LEARN) transmission gear display selection

FUEL (OFF, SPO, CST, dyn, d09) select fuel sender type

(SET LO, range, DONE) low fuel light and range setup

CL CAL adjust clock calibration

INFO display gauge revision code on speedometer

odoMK- one-time odometer preset

POWER & GROUND

The gauge is a direct plug in. Constant battery power and key switched power are supplied by the stock harness

along with ground.

STATUS AND WARNING INDICATORS

Several indicators are supplied on the stock wiring harness. Some of these may not be active on your motorcycle.

These include the security, engine, ABS, and low fuel.

LOW VOLTAGE WARNING

When the voltage drops below the warning limit with the engine running, LO and your current voltage will be

displayed. (default warning limit is 11.0V)

SPEEDOMETER & TACHOMETER

The speedometer and tachometer signals are read from the engine control module (ECM) over a data bus.

The speed can be calibrated to allow for differences in tires or gearing; calibration is discussed later.

The tach bar displays RPM x1000 with a range of 7000 RPM. The RPM can also optionally be shown on the message

display.

CLOCK

The clock uses a 12 hour format and can be set by pressing and holding the switch while the clock is displayed.

After the switch is held for a few seconds the hours will begin flashing. Momentarily pressing the switch will change the

hours, holding the switch will move to the minute set, and the minutes will begin flashing. Momentarily pressing the switch

will now change the minutes. Holding the switch will exit the clock set mode.

IMPORTANT NOTE! This gauge has an odometer preset option that is only available one time in the first 100 miles

(160km) of operation. See “Odometer preset” for instructions.

B V

MPH

km/h

RPM

1 2 3 4 5 6

Summary of Contents

Page 1 - MODEL MCL-3204

MAN# 650284:F MODEL MCL-3204 3-3/8” SPEEDOMETER/TACHOMETER for 2004 – up GAUGE SETUP AND CALIBRATION The setup menus are entered by holding

Page 2 - MAN# 650284:F

MAN# 650284:F MOUNTING The gauge will mount using the original housing, grommet, and screws. Unbolt the two screws from the back plate at the

Page 3

MAN# 650284:F nIgHtnIgHtnIgHtnIgHt Night Dimming Your display system has a dimming feature that dims the display intensity automatically at night.

Page 4

MAN# 650284:F PERF PERF PERF PERF Performance menu setup The performance readings can be turned on or off. When they are turned off the odometer

Page 5 - Troubleshooting guide

MAN# 650284:F FUNCTION SWITCH The function switch on the side of the dash panel allows access to all of the mileage, RPM, and performance inform

Page 6 - SERVICE AND REPAIR

MAN# 650284:F SERVICE AND REPAIR DAKOTA DIGITAL offers complete service and repair of its product line. In addition, technical consultation is a

Comments to this Manuals

No comments

Dakota-digital MCL-3204 User Manual

Browse online or download User Manual for For the car Dakota-digital MCL-3204. Dakota Digital MCL-3204 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Dakota-digital MCL-3204