Dakota-digital MCL-3212 User Manual download pdf

MAN# 650378

MODEL MCL-3212

SPEEDOMETER/TACHOMETER for 2012 – up Dyna and Softail with 4” gauge

GAUGE SETUP AND CALIBRATION

The setup menus are entered by holding the switch in while turning the key on. The menus are as follows:

Menu Description

dIag (EngInE, seCURE, ABS, DONE) read diagnostic codes

ADJvST (FASTER, SLOWER) (75 - 125) adjust calibrate speed

vnIt (MPH, km/h ) select speed unit

S SET (OFF, 500 - 7500) miles to service setting

PERF (ON, OFF) turn on/off performance displays

NIGHT (ON, OFF) turn on/off automatic night dimming

UPDATE (1, 2, 3) set digital rpm update rate

WXARN

RPM

(shown on bar graph) set rpm shift warning point

WXARN

(9.0- 12.1) set low volt warning point

SET FC (HEAD F, HEAD C) select temperature unit

HI F-C (200F - 420F or 93C - 215C) set temperature warning point

GEAR (DONE, PRESET, LEARN) transmission gear display selection

FUEL (OFF, SPO, CST, HD) select fuel sender type

(DONE, TEST, RESET, ADJUST) low fuel light setup

Range (ON, OFF) Enable distance to empty reading

(done, rESET) Reset initial range learn

INFO display gauge revision code on speedometer

odoMK- one-time odometer preset

POWER & GROUND

The gauge is a direct plug in. Constant battery power and key switched power are supplied by the stock harness

along with ground.

STATUS AND WARNING INDICATORS

Several indicators are supplied on the stock wiring harness. Some of these may not be active on your motorcycle.

These include the security, engine, ABS, and low fuel.

LOW VOLTAGE WARNING

When the voltage drops below the warning limit with the engine running, LO and your current voltage will be

displayed. (default warning limit is 11.0V)

SPEEDOMETER & TACHOMETER

The speedometer and tachometer signals are read from the engine control module (ECM) over a data bus.

The speed can be calibrated to allow for differences in tires or gearing; calibration is discussed later.

The tach bar displays rpm x1000 with a range of 7000 rpm. The rpm can also optionally be shown on the message

display.

CLOCK

The clock uses a 12 hour format and can be set by pressing and holding the switch while the clock is displayed.

After the switch is held for a few seconds the hours will begin flashing. Momentarily pressing the switch will change the

hours, holding the switch will move to the minute set, and the minutes will begin flashing. Momentarily pressing the switch

will now change the minutes. Holding the switch will exit the clock set mode.

IMPORTANT NOTE! This gauge has an odometer preset option that is only available one time in the first 100 miles

(160km) of operation. See “Odometer preset” for instructions.

B V

MPH

km/h

RPM

ABS

1 2 3 4 5 6

Summary of Contents

Page 1 - MODEL MCL-3212

MAN# 650378 MODEL MCL-3212 SPEEDOMETER/TACHOMETER for 2012 – up Dyna and Softail with 4” gauge GAUGE SETUP AND CALIBRATION The setup menus

Page 2 - MAN# 650378

MAN# 650378 MOUNTING The gauge will mount using the original housing, grommet, and screws. Unbolt the two screws from the back plate at the ba

Page 3

MAN# 650378 SPEED CALIBRATION The speed calibration is not required unless you have changed out the stock transmission, pulley, or tires. ADJvST A

Page 4

MAN# 650378 Set FCSet FCSet FCSet FC Temperature sender setup The temperature gauge can read the stock head temperature sensor from the ECM. • Pr

Page 5

MAN# 650378 FUEFUEFUEFUELLLL Low fuel light and distance to empty setup If the range feature is turned on, the range reading will initially show t

Page 6 - Troubleshooting guide

MAN# 650378 Troubleshooting guide Problem Possible cause Solution Gauge will not light up. Red/Orange wire does not have

Comments to this Manuals

No comments

Dakota-digital MCL-3212 User Manual

Browse online or download User Manual for For the car Dakota-digital MCL-3212. Dakota Digital MCL-3212 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Dakota-digital MCL-3212