MAN 650066:D 1 VACUUM FLUORESCENT DIGITAL DASHBOARD SERIES 3 NOW WITH SOLID STATE SENSOR TECHNOLOGY INSTALLATION AND
MAN 650066:D 10 SPD + This terminal is used to supply power to Dakota Digital speed sensor SEN-01-5. This supplies 5V DC to the sen
MAN 650066:D 11 systems with one message display the speed/performance and rpm/warn messages will use the same display. To enter DEM
MAN 650066:D 12 WTR – This is the ground reference used for two-wire water temp sensors. This will connect to one of the wires from
MAN 650066:D 13 FUEL SND The fuel gauge sending unit is not normally supplied because the display system can use the existing fuel s
MAN 650066:D 14 GEAR (1 wire) The GEAR terminal is used for the gear shift indicator. The indicator is built into every system, but
MAN 650066:D 15 CHECK ENG (-) The check engine terminal is used with fuel injection ECM’s to display engine problems and trouble cod
MAN 650066:D 16 Setting up the control box Below is a list of all of the setup menus. You must have SW1 wired to enter setup; des
MAN 650066:D 17 SPEEDOMETER SETUP/CALIBRATION There are two main methods for calibrating the speedometer, auto cal and adjust. Auto
MAN 650066:D 18 (Auto Cal continued) NOTES: You do not have to drive at a constant speed nor do you have to avoid stopping during Au
MAN 650066:D 19 Speed Output (OUTPUTOUTPUTOUTPUTOUTPUT) If a speed signal is needed for an ECM or cruise control, the SPD OUT termin
MAN 650066:D 2 Thank you for purchasing the Vacuum Fluorescent Digital Dashboard from DAKOTA DIGITAL, the leader in custom automot
MAN 650066:D 20 Display update setup (UPDATEUPDATEUPDATEUPDATE) The display update rate can be adjusted so the reading on the tach
MAN 650066:D 21 WATER TEMP SETUP The water temp setup allows you select the units the temperature is displayed in, Fahrenheit or Cel
MAN 650066:D 22 Temp sensor test (testtesttesttest) This menu will allow you to check the resistance the control box is reading fr
MAN 650066:D 23 Oil pressure sensor test (testtesttesttest) This menu will allow you to check the voltage the control box is readi
MAN 650066:D 24 Fuel sensor setup (SENDERSENDERSENDERSENDER) This menu is used to select the fuel level sensor type. The table ab
MAN 650066:D 25 Exit fuel setup (donedonedonedone) This will allow you to exit the fuel setup and go on to the next setup menu. •
MAN 650066:D 26 BUS INTERFACE MODULE SETUP The bus interface modules (BIM) are a future product added to Dakota Digital instrumentat
MAN 650066:D 27 TROUBLESHOOTING GUIDE This is a list of some problems and their solutions which may be encountered when installi
MAN 650066:D 28 Symptom Possible Problem Solution ------------------------------------------------------------------------
MAN 650066:D 29 Symptom Possible Problem Solution ------------------------------------------------------------------------
MAN 650066:D 3 WARNING The vacuum fluorescent displays are made of glass and should be handled with care. MOUNTING UNIVERSAL DISP
MAN 650066:D 30 Symptom Possible Problem Solution ------------------------------------------------------------------------
MAN 650066:D 31 Setting the time Through lens: Using a small, thin object such as a pen or hairpin, press “set” buttons through fr
MAN 650066:D 32 VFD3 Specifications SUPPLY Voltage Input (+12) Range 8 to 22 V INPUTS Active High Low Max Min High High, Left, Ri
MAN 650066:D 4 MOUNTING KITS INTO ORIGINAL DASHES Some kits will include a separate mounting instruction sheet so please see that
MAN 650066:D 5 GAUGE SYSTEM FEATURES Mileage readings • Million mile odometer • Two (A/B) re-settable trip mileage (0-9999.9) • R
MAN 650066:D 6 MESSAGE DISPLAYS On systems with two message displays, Switch 1(SW1) will toggle between the speed message displays
MAN 650066:D 7 CONTROL BOX MOUNTING Once the display panel is in place, mount the control box within reach of the ribbon cable on t
MAN 650066:D 8 TACH POWER GROUND WARN DIM (+) SPD + SPD SND SPD - SPD OUT SW2 (-) SW1 (-) ADJ SND ADJ - WTR SND WTR - OIL + OIL SND
MAN 650066:D 9 POWER Connect the POWER terminal to accessory +12V power from the fuse panel or vehicle wiring harness. This termin
Comments to this Manuals